haspunk.blogg.se - Mototrbo cps 15.5 build 797

#Mototrbo cps 15.5 build 797 install#
#Mototrbo cps 15.5 build 797 software#
#Mototrbo cps 15.5 build 797 code#
#Mototrbo cps 15.5 build 797 Pc#

MOTOTRBO CPS v15.5 build 797 EMEA Customer Programming Software for Windows + Tuner v15.5 build 235 + FirmwareSoftware works on Windows 7, 8, 8.1, 10 (x86 and 圆4).

Introduction to MOTOTRBO Connect Plus multisite di.Item: 222963816400 MOTOTRBO CPS v15.5 build 797 EMEA + Tuner v15.5 build 235 + Firmware.

MOTOTRBO "Newbie" questions about programming and CPS.

Multisite Capacity Plus Cheat Sheet (Updated).

I've tried to list the most common programming problems - if I've missed something, please add a comment here or have a look at the comments to see if anyone else asked the same question. Or contact a Motorola Reseller by clicking here. Otherwise you'll have to contact the company who sold you your radio. My problem isn't listed here, what now? If you work for a Motorola Platinum Partner or Distributor in EMEA, you can contact me directly. In either case, you will need to contact the company who sold you this radio and request support from them. grey market) or have downloaded a (pirate) copy of the CPS from the internet. Generally speaking, there are two possibilities: either you purchased the radio from another region (i.e.

Like nearly all Motorola radios, your MOTOTRBO radio has a regional ID.

#Mototrbo cps 15.5 build 797 code#

When I read a new radio, the CPS shows error code #1027 codeplug version not supported? Go to Edit>Preferences and tick Clone Radio Identity. If I clone my radio, the Radio ID is not overwritten? Make sure the radio is properly powered during this process and that you don't mistakenly unplug the cable - otherwise you'll understand what some people mean by "bricked".

#Mototrbo cps 15.5 build 797 Pc#

It takes about two minutes depending on the model and how good your PC is. I've produced a number of tutorial videos and these are available on YouTube.

If this is your only radio, simply change the Radio IP address in the codeplug or just switch off WiFi/unplug the LAN cable when programming your radio. The reason is that Windows is somehow allocating a lower device metric to the MOTOTRBO radio and your PC now thinks it's the new network connection to use. This seems to occur mostly with Windows 7 PCs.

Click Properties then go to Internet Protocol Version 4.

Right click the LAN or WiFi connection.

If you are going to be programming a lot of radios, the easiest solution would be to change the IP address range allocated to your PC on your LAN/WLAN network so that it is not in the same range as the radio.Īs soon as I plug the radio into the PC, I loose all network connectivity? The fix is to allocate a static metric to your LAN/WLAN connection: The default IP address used for this connection is in the 192.168.10.x range (usually the radio is.

When your radio is connected to the PC, Windows sets up a network connection to the radio. When I try to read the radio I get an error code #595?Įrror 595 is generally caused by an IP address conflict. Windows will give a warning when installing this, you can ignore this warning.

#Mototrbo cps 15.5 build 797 install#

The drivers are not signed and you need to install them manually by selecting "Have Disk" and pointing to C:\Program Files\Common Files\Motorola\MOTOTRBO Driver. This should only occur with Windows XP and 2000. When I connect the radio to my PC, Windows asks for a driver? As far as I know, Windows 7 and 10 do not have this problem. This will only happen when you connect a radio. This is correct, there is no "intelligence" or level conversion in the programming cable. When I plug the programming cable into the PC, Windows does not make the "USB Start" sound? The firmware version in the radio is newer than that which the CPS can support. The version of CPS I have gives error code #1057 when I read my new radio?